REVO カーボンコンポジットシャフトのお手入れ方法

REVOシャフトについて

SHAFT DIAMETER. REVO carbon composite shafts diameters must never be altered. Any sanding, polishing, or abrasive treatment could compromise the micro-thin layers of carbon fiber and will immediately void the shaft’s warranty. Additionally the use of abrasives on a REVO shaft can release potentially harmful carbon fiber dust. REVO CARBON COMPOSITE PLAYING SHAFTS (12.4 & 12.9)Shaft Model Min. Shaft Diameter Min. V-Tek TipSilencer Thickness Min. FerruleLength Min. Vault PlateThicknessR-12.4-website.png 0.488″(12.4mm).010″(.254mm)N/A 0.060″(1.5mm)R-12.9-website.png0.508″(12.9mm).010″(.254mm)N/A 0.060″(1.5mm)REVO 12.4 & 12.9 PLAYING SHAFT TIP REPLACEMENT. REVO Carbon composite shafts have no ferrule. The front end is made up of the Predator V-TEK vault plate, red V-TEK Tip Silencer, and eight-layer Victory Tip. Because the shaft cannot be sanded, replacing the tip, and/or the tip silencer should only be done by an authorized Predator Repair Center equipped with the proper tools to protect your REVO shaft. In the event that you choose to replace the tip on your shaft through a non-authorized cue technician, the red V-TEK Tip-Silencer must remain at least .010” (0.25mm) thick to maintain the shaft’s integrity. Any reduction in the tip-silencer below .010” (0.25mm) will void the shaft’s limited-lifetime warranty and compromise its performance.REVO CARBON COMPOSITE BREAK SHAFTS (BK-R)Shaft Model Min. Shaft Diameter Min. R-Break Shield Thickness Min. FerruleLength Min. Vault PlateThicknessBK-R-website.png 0.508″(12.9mm) .010″(.254mm)N/A 0.060″(1.5mm)REVO BK-R BREAK SHAFT TIP REPLACEMENT. REVO BK-R Carbon composite shafts have no ferrule. The front end is made up of the Predator V-TEK vault plate, gray R-Break Shield, and seven-layer BK Hybrid Tip. Because the shaft cannot be sanded, replacing the tip, and/or the R-Break Shield should only be done by an authorized Predator Repair Center equipped with the proper tools to protect your REVO shaft. In the event that you choose to replace the tip on your shaft through a non-authorized cue technician, the gray R-Break Shield must remain at least .010” (0.25mm) thick to maintain the shaft’s integrity. Any reduction in the R-Break Shield below .010” (0.25mm) will void the shaft’s limited-lifetime warranty and compromise its performance.WARPAGE. REVO carbon composite shafts feature a limited-lifetime warranty against warpage.ABUSE. REVO carbon composite shafts are not designed to withstand extensive lateral pressure. They should not be bent excessively, hit on the table or other objects, or treated with any abrasives, solid or liquid. We recommend protecting your shaft with a case and joint protectors.REVO SHAFT FINISH MAINTENANCE. REVO carbon composite shafts should never be sanded or modified. Sanding the surface of the REVO shaft will damage the exterior finish and weaken the shaft’s structural integrity and release potentially harmful materials that could affect your health. Any sanding, polishing, or treatment of the surface of the shaft with chemicals or abrasives of any kind will void the shaft’s limited-lifetime warranty and negatively affect the shaft’s longevity and performance. Never use talcum powder, baby powder, hand chalk, or other shaft treatments on a REVO carbon fiber composite shaft.To clean the surface of your REVO carbon composite shaft, you can use one of the following two solutions: REVO Wipes, or Isopropyl Alcohol (90%) cleaning.Step 1. Wipe the shaft with the included microfiber cleaning cloth, brushing away any lose dirt, dust and debris.Step 2. Using a REVO wipe or soft cloth towel with a reasonable amount of Isopropyl Alcohol (90%), work up and down the shaft, from the joint end toward the tip while rotating your hand around the shaft’s circumference. You may see dirt on the towelette – this is normal. Continue to work the shaft until all areas have been thoroughly wiped, allowing 1-2 minutes for the surface to dry.THE ORIGINAL UNI-LOC® JOINT. We recommend cleaning the Original Uni-Loc® Quick Release joint when you first receive your cue and every six months thereafter. These joints are precision manufactured to exact tolerances and even a modest amount of dirt can create a problem. You can use a Q-Tip dipped in Isopropyl Alcohol (90%) to clean the inside threads and bore of the shaft insert. Clean the joint pin and threads with alcohol and a clean rag. We recommend the use of joint protectors to help keep your joint clean and to protect it from damage.PREDATOR CUSTOMER SERVICE. If you have any questions or need any maintenance work done on your Predator product, please contact customer service via this web site.

お使いのキューバットのジョイント部直径が.839 "から.842 "の範囲内であれば、ピンがバットの中央に正しく配置されている場合、ジョイント経の移行はスムーズに感じられるはずです。